咨询电话：131 6657 0872

丁基钢板腻子止水带是采用优质高分子材料与镀锌板复合而成的橡胶止水带产品。其中橡胶腻子的主体材料具有耐老化性能优良，特强的自粘性；夏季高温不流淌。冬季低温不发脆；并具有优异的耐水、耐酸碱和耐老化性能；使用寿命长，产品本身无毒，环境良好。为了承受一定的弯曲和压力。中间来有0.4或0.6mm的钢板。该止水带对建筑缝之间提供可靠的防水、防渗功能。
Butyl steel plate putty water stop belt is made of high quality polymer material and galvanized sheet compounded rubber water stop products. Among them, the main material of the rubber putty has excellent aging resistance and strong self adhesion, and the high temperature does not flow in summer. Low temperature in winter, no brittle, and has excellent water, acid and alkali resistance and aging resistance, long service life, the product itself non-toxic, good environment. In order to withstand certain bending and pressure. There are 0.4 or 0.6mm steel plates in the center. The water stopping belt provides reliable waterproof and impervious function to the building joint.
钢板橡胶止水带是将镀锌钢板插入硫化好的橡胶中，橡胶采用国产一级特种橡胶与促进剂量、防老剂等，经混炼、挤压后与镀锌钢板粘合而成的一种新型接缝止水产品。这种止水带可以有效地防止各种荷载下产生的弹性、变形及施工缝的温差变化，起到坚固密封。并且能有效的防止施工缝漏水，渗水，并对各种作用力起到缓冲作用。本产品具有耐老化性能优良，特强的自粘性；夏季高温不流淌。冬季低温不发脆；并具有优异的耐水、耐酸碱和耐老化性能；使用寿命长，产品本身无毒，环境良好。为了承受一定的弯曲和压力。中间来有0.4或0.6mm的钢板。本产品可以对建筑缝之间提供可靠的防水、防渗功能。当使用普通橡胶止水带时，如果建筑结构变形大时，橡胶止水带则随着结构的沉降，其横向截面拉长，变薄，超过其疲劳变形极限时，很可能会形成新的渗漏缝隙。我们可以根据用户要求生产各种非标型号的产品，并满足各种工程上的实际需要。适用于许多大型建筑领域，尤其是在水压高和结构变形量较大时，其止水效果更为明显。
Steel plate rubber sealing strip is inserted into the good will of galvanized steel plate vulcanized rubber, rubber made of a special rubber **oxidant and promoting dose, etc., a new type of sealing products through mixing, extrusion and galvanized steel plate bonding. The water stopping belt can effectively prevent the elasticity, the deformation and the temperature difference of the construction joint caused by various loads, and the utility model can be firmly sealed. Besides, the utility model can effectively prevent the construction joint from leaking, seeping water and buffering the various forces. This product has excellent aging resistance, strong self adhesion; high temperature does not flow in summer. Low temperature in winter, no brittle, and has excellent water, acid and alkali resistance and aging resistance, long service life, the product itself non-toxic, good environment. In order to withstand certain bending and pressure. There are 0.4 or 0.6mm steel plates in the center. The product can provide a reliable waterproof and impervious function to the building joints. When using the ordinary rubber sealing strip, if the building structure of large deformation, the rubber sealing strip with the settlement of the structure, the transverse section of elongated, thin, more than the fatigue limit of deformation, it is likely to form a new leakage gap. We can produce various non-standard products according to user's requirements, and meet the actual needs of various projects. The utility model is suitable for many large-scale construction fields, especially when the water pressure is high and the structure deformation is large, the sealing effect is more obvious.
我公司可以生产各种规格的钢板腻子止水带产品，并可根据用户要求，生产各种非标型号的产品，满足工程上的实际需要。1、主要应用范围：隧道、地铁、堤坝、涵洞、水利水电工程中施工缝、高层建筑地下室、地下停车场等主要工程施工缝。
Our company can produce all kinds of steel plate putty, water stop belt products, and according to user requirements, the production of various non-standard model products, to meet the actual needs of the project. 1, the main application areas: tunnels, subways, dams, culverts, water conservancy and hydropower projects in the construction joints, high-rise buildings, basement, underground parking and other major construction joints.
钢板腻子止水带的施工方法及注意事项
Construction method and points for attention of steel plate putty water stop belt
A、将钢板腻子止水带膨胀腻子连接处搭接100mm，用手压紧排除空气靠其自身粘接牢固，并加固轧丝后重新贴上保护膜。
A, the steel plate, putty, waterproof belt, expansion putty joints overlap 100mm, hand pressed to exclude the air, by its own bonding firm, and strengthen the rolling silk, again affixed with protective film.
B、将钢板膨胀腻子止水带安放在墙体的中间位置，用铁丝固定在钢筋上，止水带略高于混凝土介面。
B, the expansion of steel plate, putty, waterproof belt placed in the middle of the wall, with iron wire fixed on the steel bar, the water stop is slightly higher than the concrete interface.
C、再次浇注前，将橡胶止水带下端的保护膜取掉，混凝土浇注至钢板膨胀腻子宽度的1／21／3处，在二次浇注前将上端保护膜取掉，再进行浇注。而采用钢板橡胶止水带时，两边的钢板与周围的混凝土结构的粘接极强，同是钢板与橡胶粘接极其牢固。当结构变形时，只存在橡胶部分拉长，变薄，而钢板与混凝土、钢板与橡胶之间不会产生新的渗漏缝隙，因此，用钢板橡胶止水带即增强了结构变形时的防渗性能，同时对整个工程的防渗止水起到了重要的质量保证。
C, again before pouring, the rubber sealing tape at the end of the protective film to take off, concrete pouring to steel expansion putty width of 1 / 21 / 3 place, in the two pouring before the end of the protective film to take off, and then pouring. And the use of steel plate rubber water stop, both sides of the steel plate and the surrounding concrete structure of adhesion is very strong, with the steel plate and rubber bonding is very strong. When the deformation of the structure, only the rubber part elongate, thin, but not between steel and concrete, steel plate and rubber leakage gap, new so that enhances the **-seepage performance of structure deformation when using steel plate rubber waterstop, and seepage of the whole project played an important quality assurance.
钢板丁基腻子止水带安装方法：
Installation method of steel plate butyl putty water stop belt:
1、钢板橡胶腻子止水带安放在墙体的中间位置，用钢丝固定钢筋上，止水带略高于混介机。（如图）
1. The steel plate, rubber putty and water stop belt are placed in the middle of the wall. The steel bar is fixed on the steel bar, and the water stopping belt is slightly higher than the mixing machine. (as in Fig.)
2**次浇筑前，将腻子止水带下段的保护膜去掉，混凝土浇注至钢板橡胶腻子止水带宽度的二分之一处，在二次浇注前将上端保护膜取掉，再进行浇注。3、钢板橡胶腻子止水带接头处的处理，将钢板橡胶腻子止水带连接处搭接100mm,用手压紧排除空气靠自身粘接牢固，并加固轧丝重新贴上保护膜。
2, the first time before pouring, the protective film waterproofing belt section removed, 1/2 concrete pouring to the width of the strip steel rubber putty, in two before pouring the upper protective film is removed, and then pouring. 3, steel sheet, rubber putty, sealing tape joint treatment, the steel plate, rubber putty, water stop joint 100mm overlap, hand pressing, excluding air, by their own bonding firm, and strengthen the rolling wire, re affixed protective film.
GB(SR)钢板丁基腻子止水带规格有：100×6、150×6、200×6、250×6、300×6、350×6、400×8、500×10单位（mm)。
GB (SR) steel plate butyl putty water stop belt specifications are: 100 * 6, 150 * 6, 200 * 6, 250 x 6, 300 x 6, 350 x 6, 400 * 8, 500 * 10 units (mm).